EXSYS USB to 8S Serial RS-232 ports Installationshandbuch PDF herunterladen

Because the designs of computers are different, only general installation instructions are

given. Please refer your computer’s reference manual whenever in doubt.

1. Connect the USB cable to the USB B Connector of the module.

2. Plug the included power supply into the 5V Connector (only EX-1338IS).

3. Now connect the other end from the USB cable ( A-Plug) to the A-Connector at

your PC.

HARDWARE INSTALLATION :

6 5

1338

English

1338

English

Die EX-1338IS und EX-1338HM sind Module mit Umsetzung von USB auf acht

RS-232 Schnittstellen mit FIFO 16C550 Ports für den Anschluss von High Speed

Seriellen RS-232 Peripherie Geräten (z.B. Modem, Plotter usw.) Die USB Modu-

le sind Hot Plug & Play. Für die Einstellungen der I/O Adressen und Interrupts

sind keine Jumper und Einstellungen notwendig. Sie werden vom System BIOS

und beim Installieren des Betriebssystems automatisch vorgenommen. Die Ex-

1338-IS ist zusätzlich mit 15KV Surge Protection und 2.5KV Optical Isolation

ausgerüstet und wird mit einem Netzteil ausgeliefert.

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

Kompatibilität: USB 1.1 & 2.0 Anschluss

Betriebssysteme: WIN 9.x/ME/2000/XP/Server 2003/Vista/Linux/MAC

Anschlüsse: 8 x 9 Pin Sub-D Stecker, 1 x USB B-Buchse, 1 x 5V Buchse

Lieferumfang: EX-1338IS bzw. 1338HM, Anleitung, CD, USB Kabel

Zertifikate:

CECE

/ FCC / RoHS / WEEE DE97424562 / WHQL

DRIVER INSTALLATION :

JUMPER EINSTELLUNG & ANSCHLÜSSE:

ACHTUNG !!!

Nur zur Verwendung mit im Lieferumfang enthaltenem Netzteil !!!

5 Volt Buchse:

Betriebs LED

S1-S8 8 x 9 Pin Stecker Seriell RS-232

5V Buchse für

externes Netzteil

USB B-Buchse

PC-Anschluss

CLEANING :

For cleaning please use only a dry fluffless cloth and remove the dirt with gently pressu-

re. In the area of the connectors please make sure that no fibres from the cloth remain

in the connectors. Attention! Never use a moist or wet cloth for cleaning!

Bedienungsanleitung

Vers. 1.0 / 09.10.07

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Seriell 9 Pin D-SUB Stecker:

DB 9M:

USB B Buchse:

USB 2.0 B-Buchse:

Pin Signal Pin Signal

1 VCC 3 DATA+

2 DATA- 4 GND

Achtung!

Stecker nie umge-

kehrt oder mit

Gewalt einstecken.

Windows 9.x and ME:

Windows will recognize a new “FT232R USB UART“ and open the hardware assistant.

Please choose manual installation and put the driver CD into your CD-Rom drive ( as

sample D: ) . Now enter the Path “D:\USB_to_IO\FTDI\Win2000_2003_XP_VISTA”

into the box for the Path/Source and click at >next/continue<. Now Windows search for

the drivers in the specified directory. Follow the hardware assistant and finish the instal-

lation. If Windows recognizes other new devices repeat the above described steps.

Attention! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find

one more new „USB Serial Port„ as sample (COM5). If you see this or similar entries

the module is installed correctly.

INSTALL THE PERIPHERAL DEVICE:

The speed from the serial ports can be set to the maximum baud rate of 115.2Kbaud.

With double click select for example >Device manager< > USB Serial Port (COM5)<.

Now you can select the different settings of baud rate, stop/start-bits etc. This setting

you can use also for the other COM ports.

Windows 2000 XP Vista Server 2000 and Server 2003 (32-bit):

Windows will recognize a new “FT232R USB UART“ and open the hardware assistant.

Please choose manual installation and put the driver CD into your CD-Rom drive (as

sample D: ) . Now enter the Path “D:\USB_to_IO\FTDI\Win2000_2003_XP_VISTA”

into the box for the Path/Source and click at >next/continue<. Now Windows search for

the drivers in the specified directory. Follow the hardware assistant and finish the instal-

lation. If Windows recognizes other new devices repeat the above described steps.

Attention! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find

one more new „USB Serial Port„ as sample (COM3). If you see this or similar entries

the module is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 to 256.

DRIVER INSTALLATION :

Windows 2000 XP Vista Server 2000 and Server 2003 (64-bit):

Windows will recognize a new “FT232R USB UART“ and open the hardware assistant.

Please choose manual installation and put the driver CD into your CD-Rom drive (as

sample D: ). Now enter the Path “D:\USB_to_IO\FTDI\Win2003_XP_VISTA(x64)” into

the box for the Path/Source and click at >next/continue<. Now Windows search for the

drivers in the specified directory. Follow the hardware assistant and finish the installa-

tion. If Windows recognizes other new devices repeat the above described steps. Atten-

tion! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find

one more new „USB Serial Port„ as sample (COM3). If you see this or similar entries

the module is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 to 256.

LINUX:

There are drivers available for Linux. The drivers are located in the folder

“D:\USB_to_IO\FTDI\Linux“ on the driver CD. They are supported by the most ver-

sions of Linux. Because each individual distribution and kernel version of Linux is differ-

ent, sadly we cant provide a installation instruction. Please refer to the installation man-

ual for standard IO ports from your Linux version !

MAC:

There are drivers available for MAC. The drivers are located in the folder

“D:\USB_to_IO\FTDI\“ on the driver CD. They are supported by the most versions of

MAC OS. Because each individual version of MAC OS is different, sadly we cant pro-

vide a installation instruction. Please refer to the installation manual for standard IO

ports from your MAC OS version !

1 2

Bedienungsanleitung 1
User Manual 2

Inhaltsverzeichnis

Seite 1 - Bedienungsanleitung

S1 S2 S3 S4 S8 S7 S6 S5 Because the designs of computers are different, only general installation instructions are given. Please refer your computer’s

Seite 2 - User Manual

S1 S2 S3 S4 S8 S7 S6 S5 2 3 4 EXEXEX---133813381338---ISISIS---HMHMHM DeutschDeutschDeutsch EXEXEX---133813381338---ISISIS---HMHMHM DeutschDeut

Kommentare zu diesen Handbüchern

Keine Kommentare

EXSYS USB to 8S Serial RS-232 ports Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Schnittstellenkarten / Adapter EXSYS USB to 8S Serial RS-232 ports herunter. EXSYS USB 1.1 to 8S Serial RS-232 ports Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schnittstellenkarten / Adapter EXSYS USB to 8S Serial RS-232 ports